We have a non-mission critical backup server which is hosting our nightly copies of MySQL databases from other servers.
The working principle is as below:
- At 2AM, server “A” creates a database backup and copies it on to external HDD.
- Server “A” then connects to the backup server and uploads a database copy there.
- Server “A” and the backup server are on the same LAN.
So, the backup server doesn’t need to be online 24/7, but on-demand instead. It would be sensible to have the server sleeping and wake up only when needed to transfer backups. This can be done by using wake on LAN messages.
We will be configuring WOL on a Debian server. Update packages list and install ethtool:
# apt-get update && apt-get install ethtool
We already have WOL enabled on BIOS, and need to check for the type of WOL our Ethernet card supports:
# ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: g Wake-on: d Current message level: 0x000000ff (255) Link detected: yes
As we may see above, Ethernet card supports Wake-on: g. Following the man page:
# man ethtool [...] wol p|u|m|b|a|g|s|d... Sets Wake-on-LAN options. Not all devices support this. The argument to this option is a string of characters specifying which options to enable. p Wake on PHY activity u Wake on unicast messages m Wake on multicast messages b Wake on broadcast messages a Wake on ARP g Wake on MagicPacket™ s Enable SecureOn™ password for MagicPacket™ d Disable (wake on nothing). This option clears all previous options.
So, we can wake our server up by using a so-called magic packet. Let us set the option on a network driver to respond to magic packets:
# ethtool -s eth0 wol g
To make this procedure automated and avoid typing the same command again after the server is restarted, we need to open the network config file
/etc/network/interfaces for editing and add the following line (in brown) to our existing network configuration:
auto eth0 iface eth0 inet static address 10.28.0.5 netmask 255.255.255.0 gateway 10.28.0.254 dns-nameservers 10.28.0.254 /sbin/ethtool -s eth0 wol g
Ensure that WOL is enabled:
# ethtool eth0 | grep Wake-on Supports Wake-on: g Wake-on: g
We now have to find the MAC address of the NIC as it will be required to wake up the backup server. MAC can be retrieved from
# cat /sys/class/net/eth0/address 00:21:00:00:00:00
Server can be sent to sleep via the pm-suspend command. It’s necessary to have the pm-utils package installed.
Send a Magic Packet
We will send a magic packet (from the server “A”) by using the wakeonlan utility. Install:
# apt-get install wakeonlan
Wakeonlan uses UDP packets and takes NIC MAC address as an argument:
$ wakeonlan 00:21:00:00:00:00 Sending magic packet to 255.255.255.255:9 with 00:21:00:00:00:00
That’s it. If you have some strict firewall rules for outgoing traffic, makes sure these allow broadcast to leave:
# iptables -A OUTPUT -p udp -d 255.255.255.255 -j ACCEPT
Note to myself. Send WOL from Mikrotik router:
[[email protected]] > tool wol mac=00:21:00:00:00:00 interface=lan-bridge
Good post, I will try.
Thanks a lot!
That worked perfectly. Thanks for the info.
This is great! Only thing I needed to do differently to get this to work was to make a small change to the line added in the interfaces file:
post-up /sbin/ethtool -s eth0 wol g
Note the addition of ‘post-up’ to the line